What is master slave and cable select?
All IDE drives have jumpers that select the “master” or “slave” role on the controller, but modern drives also have a “CS” or “Cable select” pin. This allows the IDE cable itself to select the drive’s role: all the drives have the CS jumper set, and the cable chooses the master and the slave.
What is difference between master and slave drive?
Slave drives are mostly used for storing data to protect it in the event of a system crash. Master drives usually contain the operating system to run the computer. Computers without a secondary drive set as a slave drive will store their data on the main (only) hard drive, alongside the operating system.
What does Cable Select mean on hard drive?
Cable select, also referred to by the acronym CS, is a disk drive jumper setting which automatically sets the priority of a disk drive by its position on its data cable. When cable select is enabled, the drive configures itself as a primary or secondary depending on its position in the drive chain.
What is a master and slave jumpers?
If a jumper connects pins five and six, which are the center pins on each row, it is a master. If the jumper connects pins three and four, which are the pins second to the right, it is a slave.
How do I make a master slave drive?
Answer. Answer: You simply set the jumper to Cable Select on both drives and depending on where you connected them to the cable the computer would know which is Master and which is Slave. If you are going to use Cable Select you need a special 40 conductor IDE cable that would determine master and slave connections.
What is master and slave in HDD?
In order to configure master and slave settings for hard drives, your computer’s motherboard must support multiple internal hard drives and you must have the second hard drive installed. “Master” drives typically store the operating system, while “Slave” drives are used for additional storage and backup.
How do I set master drive to IDE?
Connect the drive using the Master connector on the primary IDE cable. Set the first CD/DVD drive jumper to Master (alternatively, Cable Select can be used if you set the second CD/DVD drive selection to Cable Select). Connect the drive using the Master connector on the secondary IDE cable.
How do I change my hard drive from master to slave?
Using the arrow keys, find and select the hard drive that you attached to the computer. Change the hard drive to “Slave” status. You’ll use the “Configure” or “Change” key to do this as well. Once you see “Slave” to the right (or near) the drive’s name, you can proceed.
What is master slave disk drive?
In electronics, master/slave relationships are used to describe some of the following scenarios: In parallel ATA hard drive arrangements, the terms master and slave are used to describe drives on the same cable, but neither drive has control or priority over the other.
How do I make my hard drive the main one?
How to Make an External Drive Your Main Hard Drive
- Plug your external drive into your computer and reboot it.
- Press the appropriate key combination to enter your BIOS.
- Look for the boot order settings.
- Set your USB external drive as your first boot device.
- Save your changes and exit.
What is hard disk master slave?
In parallel ATA hard drive arrangements, the terms master and slave are used to describe drives on the same cable, but neither drive has control or priority over the other. A master clock that provides time signals used to synchronize one or more slave clocks as part of a clock network.
What type of drive uses master and slave connections?
Integrated Drive Electronic hard drives use master and slave settings to help the computer tell the two devices apart when connected to the same cable.
What should I use instead of master and slave?
Alternatives to Master-Slave Terminology
- Primary and secondary.
- Primary and replica.
- Primary and standby.
- Leader and follower.
- Conductor and follower.
- Source and sink.
- Main.
What is master and slave configuration?
Master/slave is a model of communication for hardware devices where one device has a unidirectional control over one or more devices. This is often used in the electronic hardware space where one device acts as the controller, whereas the other devices are the ones being controlled.
What is a slave master?
slavemaster (plural slavemasters) One who owns a slave. One who controls the action of a slave owned by others.
How do I boot a hard drive from slave?
BIOS Setup
- Turn on or restart the computer.
- Select “Boot” or “Advanced BIOS Features” using the arrow keys.
- Select “Hard Disk Boot Priority,” “Hard Drive Order,” “HDD Boot Priority” or similar option, if available.
- Select the secondary hard drive and press “Enter,” or press “+” to move the device to the top of the list.
Do SATA drives have master slave jumpers?
Unlike older IDE drives, SATA disks have no jumpers and it’s not necessary to configure a master/slave relationship between them. As long as you have a Windows drive installed in the system, your computer will recognize the additional drive as a secondary.
What can I use instead of master and slave?
Can I use an external hard drive as my main drive?
Using a bootable external drive in lieu of your computer’s internal hard drive can add a layer of security as well as portability to your valuable company data and installed programs.
How do I change which hard drive to boot from?
From within Windows, press and hold the Shift key and click the “Restart” option in the Start menu or on the sign-in screen. Your PC will restart into the boot options menu. Select the “Use a device” option on this screen and you can choose a device you want to boot from, such as a USB drive, DVD, or network boot.