What is the difference between Hilti HY 200-A and HY 200-r?
Hilti HIT-HY 200-A will have shorter working times and curing times than Hilti HIT-HY 200-R. The user can select product gel time suitability based on temperature of the base material and jobsite time requirements. The packaging for each is different which helps the user distinguish between the two adhesives.
What is the difference between Hilti 200 and 500?
HIT-RE 500 V3 is an epoxy with a slow cure time and HIT-HY 200 is a hybrid acrylic based adhesive with a fast cure time.
How long does it take for Hilti epoxy to cure?
Hilti HIT-RE 500 V3 is the only epoxy adhesive anchor that cures below freezing and is rated down to 23o F. Balance longer work times with shorter cure times. Hilti HIT-RE 500 V3 gives you a 25-minute working time at 72o with initial cure in four hours and full cure in six hours.
How long does Hilti 500 take to cure?
Hilti HIT-RE 500 V3 gives you a 25-minute working time at 72o with initial cure in four hours and full cure in six hours. Use Hilti Adhesive Anchor products with diamond-coring methods.
What is Hilti hy200?
– SafeSet technology: Hilti hollow. drill bit for hammer drilling. – HY 200-R version is formulated. for best handling and cure time. specifically for rebar applications.
How strong is Hilti epoxy?
Hilti HIT-RE 500 V3 has the highest bond strength on the market—60 percent higher than Hilti HIT-RE 500-SD technology (the previous market leader).
How strong is concrete anchor epoxy?
A 5/8” diameter threaded rod in a 3/4″ diameter hole embedded to a 5-5/8” depth and cured at 75 °F for 24 hours in 3,500 psi concrete will yield an ultimate pullout strength of 28,000 lbf (124 kN). At the minimum load time of 4 hours in the same conditions the ultimate pullout strength is 7,000 lbf (31 kN).
What is Hilti RE 500 used for?
Hilti HIT-RE 500 V3 is approved for use with the Hilti HIT TE-YRT Roughening Tool. The tool is used for hole preparation in conjunction with holes core drilled with a diamond core bit to allow diamond coring in cracked and uncracked concrete in all seismic zones.
What Hilti 500?
Fifteen years ago, Hilti set legendary standards for designers and contractors with the HIT-RE 500 – the first epoxy injectable mortar for post-installed anchors and rebar fixings. And because our customers needed the same high performance and maximum reliability for cracked concrete, we introduced HIT-RE 500-SD.
What is the strongest anchoring epoxy?
ULTRABOND® HS-1CC is the world’s first anchoring epoxy for cracked and un cracked concrete, formulated to be IBC compliant in both bulk and cartridge delivery systems for use in dry, damp, water-filled and submerged holes, even in the most extreme temperature and load conditions.
What size concrete anchor should I use?
As a rule of thumb, the space for the nut and washer is equal to the diameter of the wedge anchor being used. For example, if a 2×4 is being fastened to concrete with a 1/2” wedge anchor then the minimum length of wedge anchor would be 1-1/2”(2×4) + 2-1/4”(minimum embedment) + 1/2”(space for nut and washer) = 4-1/4”.
How deep should epoxy anchors be?
TIP: the hole depth should be a minimum of 4 1/2 times the diameter of the bolt (a 1/2 inch threaded rod would require a hole depth of 2 1/4 inches).
How much force can concrete anchors hold?
These concrete anchor bolts, or bolt anchors for wood, are available in several sizes and will hold up to 200 lbs. The sleeves pinch the sides of the predrilled hole and get tighter as you tighten the screw or bolt. Best uses: Concrete, concrete block, mortar and brick.
Why choose the Hilti adhesive anchor hit-Hy 200-a?
With the Hilti adhesive anchor HIT-HY 200-A, you get both. Worried about the demands of the job? Relax. We’ve formulated a special chemical anchor, HIT-HY 200-A with advanced working time, to handle just about anything the job throws at you. Hilti offers the highest performing, most reliable anchoring solutions in the industry.
Can hit-Z anchors be used on water filled holes?
Practical and versatile adhesive anchor – approved for water-filled holes. No hole cleaning required when using HIT-Z anchor rods or drilling with hollow drill bit and a compatible vacuum cleaner.
Why choose Hy 200-a V3?
Suitable even for challenging jobsite conditions – HY 200-A V3 works in hammer drilled, hollow drilled and diamond cored holes (with TE-YRT roughening tool), and at base material temperatures from -10 to +40°C. Faster curing time optimized for anchoring
Why choose hit-Hy 200-a with safeset™ technology?
HIT-HY 200-A with SafeSet™ Technology eliminates the need for manual hole cleaning, which increases productivity all while using a system that meets the new OSHA regulations for silica dust. Take productivity and reliability to the next level with Hilti HIT-HY 200-A and SafeSet™ Technology.