How do I reset my GE Triton dishwasher?
Try pressing the “Start/Reset” pad to reset the dishwasher and wait 2 minutes. If the problem persists, reset (reboot) the dishwasher by turning off power to the unit at the house circuit breaker or fuse box for 30 seconds. Restore power and the dishwasher should reset and function normally.
Why did my GE dishwasher stop working?
#1. Confirm that the power switch is on. Switches are often located under the sink or on the wall near the dishwasher. Check your home’s circuit breaker or fuse box for tripped breakers or blown fuses. Reposition any tripped breakers or replace blown fuses.
How do I reset my GE dishwasher control board?
Hold the Start button now for five seconds. The Start button should start flashing. Finally, hold the Start and Select Cycle button down for five seconds. The dishwasher control panel should now light up, and the dishwasher should be ready to go.
Where is the reset switch on a GE dishwasher?
For front-control washers, press the Start/Reset button. If you have a top-control washer, carefully open up the top of the dishwasher door and press Start/Reset, then close the door.
Is there a fuse in a GE dishwasher?
The thermal fuse shuts off power to the dishwasher if it overheats. If the thermal fuse blows, it will prevent the dishwasher from starting. To determine if the thermal fuse is defective, use a multimeter to test the fuse for continuity. If the thermal fuse does not have continuity, replace it.
Where is fuse located on GE dishwasher?
The thermal fuse is normally located on the top side of the circuit board assembly with two wires attached to it. When the thermal fuse fails, the control board will not receive power and the dishwasher will not start.
How do I know if my dishwasher motherboard is bad?
Signs of Whirlpool dishwasher control board problems
- Cycles not starting (or very delayed starting) when you press the start button or the dishwasher only accepting to run on some cycles (for example, heavy duty).
- Error codes or flashing lights on your dishwasher.
- The dishwasher failing to run completely.
What are the error codes in a GE dishwasher?
Dishwasher – Error, Fault or Function Codes
Fault Code | Definition |
---|---|
C1 | The pump out during drain has exceeded 2 minutes. |
C2 | The total pump out cycle exceeds 7 minutes. |
C3 | The dishwasher will not drain. |
C4 | Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. |
Is there a fuse on a GE dishwasher?
What do you do when your GE dishwasher won’t drain?
Check the drain hose where it connects below the sink for a blockage or a kink in the hose. New dishwashers come with a white corrugated drain hose which should be used. Re-using old, worn out drain hoses may promote kinking or a blockage. Make sure the kitchen sink drain is not clogged.
How to reset my ge Triton dishwasher?
TriClean™ wash system with 3 wash arms and six levels of wash undefined
How to level a GE Profile fridge?
Remove the grille over the legs. Find the grille at the bottom of the refrigerator.
How to troubleshoot a GE Profile washer Spin Cycle?
– Press Start to resume the cycle or you can select Drain & Spin and press Start. – If water remains in the washer, check for a pinched or flattened drain hose. – If you clear a clog, press START to resume your cycle or you can select Drain & Spin and press Start. – If the water drains, then the clog is clear.
How do you load a GE dishwasher?
The third rack/tray is only meant to be used with a GE Appliances third rack dishwasher to hold silverware,cooking utensils and other small items.