How do you mix procion MX dye?
You just mix 8 oz of warm water to the following amount of dye: Colors with no * need 2 teaspoons of dye. Colors with one * need 4 teaspoons of dye. Colors with two * need 8 teaspoons of dye.
How long does procion MX Dye last?
Once the dye powder is mixed with water it should be used within 3 days for the best, brightest results but some colors work fine for up to 2 weeks. If the dyes are combined with soda ash, they weaken FAST – they may last for an hour or so – again each color is different.
How do you mix procion powder?
The fibre reactive Procion MX dye powders should, for convenience, be mixed into a 1% solution; e.g. 5g of powder in a small vessel stirred into a smooth paste with a little cold water and made up to ½ litre with water (less than 50°C) from the tap.
How long does procion dye need to set?
8-24 hours
Fiber reactive dyes, such as Procion MX dyes or the Tulip One-Step tie-dye kits, need to sit for 8-24 hours for the best results.
How do you use procion powder dye?
In each pot mix, 1 teaspoon each of procion and soda ash with 2 tablespoons of salt. The soda ash acts as a fixative and the salt pushes the colour deep into the fabric. Add a small amount of warm water and paste it down using a plastic spoon or brush- get rid of the lumps until it’s smooth.
Does procion dye go bad?
Procion MX dye powders, like other fiber reactive dyes, will eventually go bad on the shelf, as they react with tiny amounts of moisture. They will last longer if tightly sealed in jars than if kept in plastic bags, but in any case will eventually go bad eventually, if you keep them long enough.
Why do you put salt in tie-dye?
When cotton yarn or fabrics are dyed, salt is added to the dye bath as a mordant to help the fibers absorb the dye. For wool or nylon, the acid in vinegar acts as a mordant in the dye bath to help the fibers absorb dye.
Which two colors Cannot be made by mixing colors together?
Red, yellow and blue are the primary colors. Primary colors are the most basic colors. You can’t make them by mixing any other colors. Orange, green and purple are the secondary colors.
What is Synthrapol used for?
Synthrapol is a liquid detergent used as a prewash and afterwash for dyed or painted fabrics and as a wetting agent for fabric dyes and paints.
What happens if you use tie-dye after 72 hours?
How long can I keep a dye once it has been mixed with water? Do not add water to dye until you are prepared to apply it. Apply dye within 24 hours after mixing. Dye left unapplied after 24 hours will begin to lose concentration and will result in noticeably weaker color intensity.
How long can you keep tie-dye after mixing it?
Once the dye has been activated by mixing with water, it will last up to 72 hours, so we generally recommend using your dye within that timeframe.
Does vinegar help tie-dye?
Try soaking your tie dye in equal parts white vinegar and cold water for 30 minutes after you initially rinse out the dye from your garment. The vinegar helps with colorfastness. After the first couple of washes, wash tie dye in cold water to prevent dye from fading. Use gentle, color-safe detergents.
Do I need to soak tie-dye in vinegar?
Contrary to popular belief, you do not need vinegar to set tie-dye on cotton. Unless your tie-dye kit specifically tells you to use vinegar, you don’t need it. Note: Vinegar can help set some acid dyes on animal fibers like silk or wool – but it’s not necessary to set dye on cotton fabrics.
What does soda ash do in tie-dye?
And what does it have to do with tie dye? Soda ash is also known as sodium carbonate, but the most important thing you need to know about it is that soda ash can help prepare the fibers of your fabric to better absorb dyes and therefore produce brighter results.
Can I use vinegar instead of soda ash?
Soda Ash is also very hard on these fabrics, so use half as much, and don’t cure for more than 4-6 hours, or use the vinegar / microwave method instead of using Soda Ash. It is always good to pre-wash your fabric and garments; fabric softeners, oils, and other finishes can prevent the dye from absorbing into the fiber.
Does the dye mixer applet include the Procion MX mixing primary colors?
The Dye Mixer Applet does not include some of the Procion MX mixing primaries, and it does include some premixed colors. After trying all of the above color mixing guidelines that interest you, you are going to have to do some dyeing to find how you prefer to mix your colors.
Is there a way to calibrate dye color mixing?
It’s a great way to experiment with dye color mixing, but unfortunately it has not been calibrated for how much dye is required to get each color. If you wish to use it to specify exactly how many grams of each dye you should mix, you will have to create your own swatches with each of the pure unmixed colors you are using as your mixing primaries.
How much dye do I use per cup of dye?
Usually about 1 to 3 teaspoons of dye per cup of liquid will be used, depending on the depth of color desired. When ready to apply add BAKING SODA to the above mixture – 1 Teaspoon per cup.
What colours can you mix with mx-8g?
You will need, at minimum, yellow MX-8G, turquoise MX-G, and red MX-8B, plus a premixed black such as black MX-CWNA. For intermediate dye mixing, you should, in addition, get yellow MX-GR, orange MX-2R, blue MX-R, blue MX-G, and either blue MX-2G or navy blue MX-3R.